Abrasive Cloth Roll 200 mm x 30 m P36 YT-83201 YATO
Key information
Availability:Temporarily out of stock — ask for availability
Shipping cost:From 3.52 Euro
catalog number:YT-83201
Availability:
EAN code:5906083832017
Product condition:New, originally packaged
Guarantee:24 months of consumer protection
Weight:8,75 kg
By purchasing this product, you will receive 206 points from us, which you can use for shopping in our store. This applies only to customers registered in our store.
- Product description
- Product reviews (0)
Abrasive cloth roll 200 mm x 30 m P36 YATO YT-83201
Professional abrasive cloth on a cloth backing with aluminium oxide grain. The roll, 200 mm wide and 30 metres long, is intended for intensive sanding of wood, metals and selected plastics.
Technical characteristics of the abrasive cloth
P36 grit – coarse sanding
A P36 grit designation refers to grain approximately 538 micrometres in diameter. It is used for removing major unevenness, stripping old coatings, initially levelling surfaces and removing material quickly ahead of finishing work.
Cloth backing – flexibility and durability
The woven cloth backing resists tearing and stays flexible during use. It conforms to irregular surfaces and can be cut to any length without the edges fraying.
Aluminium oxide as the abrasive material
Aluminium oxide grains are hard, have sharp edges and resist high temperatures. This material delivers even sanding, a long abrasive life and consistent performance when working different materials.
Roll format 200 mm x 30 m
The 200 mm width matches standard belt sanders and allows larger surfaces to be worked. The 30 metre length allows repeated cutting into shorter sections or the preparation of long belts for intensive work.
Technical specification
| Model | YT-83201 |
| Manufacturer | YATO |
| Grit | P36 (coarse) |
| Belt width | 200 mm |
| Roll length | 30 m |
| Abrasive material | Aluminium oxide (Al₂O₃) |
| Backing | Cloth |
| Materials worked | Wood, metals, selected plastics |
Applications for P36 abrasive cloth
- Removing old coats of paint, lacquer or varnish from wooden surfaces
- Initial levelling of rough boards and timber components before finishing
- Sanding welds, removing rust and burrs from metal surfaces
- Preparing steel surfaces before painting or applying coatings
- Working plastics components that require rapid material removal
- Preparing belts for 200 mm wide belt sanders
- Hand sanding with a sanding block or paper holder
- Work in joinery, metalworking and paint shops
How to match the belt length to your sander
To prepare a belt from the roll, measure the belt circumference on your sander or check the machine's technical data. Cut the required length from the roll, leaving 2-3 cm of allowance. The ends can be joined with a purpose-made abrasive belt adhesive or the job can be handed to a professional repair service.
Use and maintenance
Before starting work, make sure the surface is free of loose contamination. While sanding, apply even pressure and guide the tool along the grain of the wood or in the direction of the surface being worked. Clean the belt of dust regularly with a brush or compressed air.
Store the roll in a dry room, away from sources of moisture and direct sunlight. Moisture can weaken the bond and reduce the effectiveness of the abrasive. Once a section has been cut from the roll, secure the edge to stop it unrolling.
When working with metals or plastics, monitor the surface temperature. Excessive sanding can overheat the material and clog the abrasive grains. In such cases, reduce the pressure or apply cooling.
Commercial information
Nobody has written a review for this product yet. Be the first to write a review.
Write a review for this product and you will receive 100 points from us that you can use for shopping in our store. This applies only to customers logged in and registered in our store.
Only registered customers can write product reviews. If you have an account in our store, log in to it, if not, create a free account and write a review.
