Knotted Wire Wheel Brush 125mm M14 GEKO G00607
Key information
Availability:In stock (ready to ship)
Shipping time:immediately
Shipping cost:From 3.29 Euro
catalog number:G00607
Availability:
EAN code:5901477104565
Product condition:New, originally packaged
Guarantee:24 months of consumer protection
Weight:0,37 kg
By purchasing this product, you will receive 20 points from us, which you can use for shopping in our store. This applies only to customers registered in our store.
- Product description
- Product reviews (0)
- Purchase history (7)
Knotted Wire Wheel Brush 125mm M14 GEKO G00607
A wire wheel brush with a knotted steel wire construction, designed for fitting to angle grinders. A tool for removing coatings, rust and contamination from metal surfaces and for preparing the substrate for subsequent stages of work.
Technical features
Knotted wheel construction
Steel wire arranged in a knotted pattern provides greater rigidity and a more aggressive action than crimped wire brushes. The wheel design allows you to reach edges and awkward areas where cup brushes are of limited effectiveness.
Hardened steel wire
The hardening process increases the hardness of the wire, giving a longer tool life and maintaining its abrasive properties during intensive work. Hardened wire copes better with removing hard coatings and firmly adhering rust.
M14 thread
The standard fitting used on most angle grinders from 500 W upwards. The M14 thread provides a secure fit and direct drive without the need for additional adapters. Before fitting, check the thread type on your grinder – older models may require an M10 thread.
8,500 rpm speed limit
The maximum operating speed is determined by the mechanical strength of the wire and the construction of the brush. Exceeding this figure can damage the tool or cause wires to break off. The grinder speed must be set within the maximum rating of the brush.
Technical specification
| Model | GEKO G00607 |
| Brush diameter | 125 mm |
| Construction type | Knotted wheel |
| Wire material | Hardened steel |
| Mounting thread | M14 |
| Maximum speed | 8,500 rpm |
| Body material | Steel |
| Compatibility | 115–125 mm angle grinders with an M14 thread |
Applications
- Removing rust from steel and cast iron components
- Cleaning welds and removing burrs after cutting metal
- Removing old paint, lacquer and protective coatings
- Preparing metal surfaces before painting or welding
- Cleaning dirt from stone and concrete
- Removing surface film and deposits from metal surfaces
- Renovating tools and metal components
- Keying surfaces before bonding or applying coatings
Use and safety
Fitting and start-up
Disconnect the grinder from the mains supply before fitting. Screw the brush onto the M14 spindle thread by hand, then tighten it with a spanner while the spindle is locked. Check the maximum speed of the grinder – it must not exceed 8,500 rpm. Once fitted, run the tool at no load for 30 seconds.
Working practices
Work with the brush tilted at 15–30 degrees to the surface being worked. Do not apply excessive pressure – the weight of the grinder is enough for effective cleaning. Check the condition of the wire regularly – if the wires are worn or bent, replace the brush with a new one. Wear safety goggles, gloves and work clothing – fragments of wire and debris may fly off during use.
Commercial information
Nobody has written a review for this product yet. Be the first to write a review.
Write a review for this product and you will receive 100 points from us that you can use for shopping in our store. This applies only to customers logged in and registered in our store.
Only registered customers can write product reviews. If you have an account in our store, log in to it, if not, create a free account and write a review.
Client: Ag...ok,date of purchase 22-01-2026 08:49
Client: Ma...to,date of purchase 30-06-2025 20:58
Client: Ma...ak,date of purchase 31-07-2024 10:50
Client: Ja...ki,date of purchase 09-04-2024 12:50
Client: Ma...to,date of purchase 30-05-2023 22:04
Client: Ma...ak,date of purchase 24-06-2022 15:05
Client: Wo...cz,date of purchase 05-03-2021 15:26
GEKO G80270 125 mm Angle Grinder with Variable Speed Control, Long Handle
Wire Wheel Brush 100 mm M14, Brass-Coated Wire / YT-4761 / YATO
Cylindrical Wire Brush for Satin Finishing Machine 120 x 100 mm G00642 GEKO